You can change your warehouse lighting with the Trilamp A18 from FANXSTAR. The 5.8G Motion Sensor adds smart controls everywhere. It gives you bright light and fewer dark areas. You get safer walkways, lower energy costs, and easier work. Key features include:
-
Custom detection settings for each use
-
IP65 waterproof build for tough places
-
Long life so you replace it less
-
External emergency kit battery backup
You can count on Trilamp A4 to work well in hard spaces.
Key Takeaways
-
The Trilamp 18 with EU 5.8G Motion Sensor gives bright light. It spreads light evenly and removes dark spots. This helps make warehouses safer for everyone.
-
Smart motion and daylight sensors help save energy. They turn lights on only when needed. The lights also change brightness by themselves.
-
The light is strong and waterproof. It can last a long time in tough warehouse places. This means you do not need to fix it often.
-
You can change the settings to fit your needs. You can pick how far the sensor sees, how long the light stays on, and how bright it gets. This helps in different parts of the warehouse.
-
It is easy to install and works with old wires. This makes it simple and quick to upgrade your warehouse lights.
Overview
Trilamp A18 Introduction
You need lights that work hard like you do. The Trilamp A18 is a smart and strong choice for your warehouse. This LED weatherproof batten uses new technology to shine bright light everywhere. The EU 5.8G Motion Sensor inside can sense movement very well. When you walk down the aisles, the lights turn on just right. You will not see dark spots or waste power.
Fanxstar Trilamp A18 comes in three lengths: 2ft, 4ft, and 5ft. Each one has a different power: 20W, 40W, or 60W. You get up to 140 lumens per watt, so your warehouse stays bright and your bills stay low. The IP65 waterproof rating lets you use it in wet or dusty places. The polycarbonate body and cover are tough and protect the light for a long time. You can put it on the ceiling or wall, and the sliding bracket makes it easy to install.
You can set how the light works. You can change the detection range, hold time, daylight level, and dimming with simple switches. Dual PD Technology changes the brightness by itself, so you save energy without trying. The light lasts up to 100,000 hours, so you do not have to replace it often.
External emergency kit, enabling independent switching between regular lighting and emergency lighting modes for flexible application scenarios. The emergency accessory can be purchased separately, a design that significantly reduces your SKUs inventory pressure while making it much easier to establish and manage your inventory reserves. This modular solution balances functionality and cost-efficiency, allowing you to optimize stock levels without compromising on lighting performance or emergency preparedness.
FANXSTAR Brand
You want to trust the company that makes your lights. FANXSTAR has been known for smart lighting since 2016. They make LED weatherproof lights with smart features like remote control, dimming, and saving energy. FANXSTAR has over 30 patents and meets many quality rules, like CB, ENEC, TUV, CE, ERP, SAA, and ISO9001-2015.
FANXSTAR sells lights to more than 90 countries. People know the brand for new ideas, good quality, and great help from start to finish.
Here is a quick look at what makes FANXSTAR strong:
|
Aspect |
Details |
|---|---|
|
Establishment Year |
2016 |
|
Company Status |
China National High-Tech enterprise specializing in LED Tri-proof lighting |
|
Product Focus |
Smart LED Tri-proof lights with remote control, dimming, timing, energy-saving |
|
Innovation & Patents |
Over 30 patents in LED field |
|
Certifications |
CB, ENEC, TUV, CE, ERP, SAA, ISO9001-2015 |
|
Product Quality |
High-quality, waterproof, dustproof, anti-corrosion, strict quality control |
|
Global Reach |
Products exported to over 90 countries and regions worldwide |
|
Reputation |
Known for innovation, reliability, customization, and customer support |
|
Product Range |
LED Tri-proof luminaires, emergency lights, PIR sensor lights, vapor tight fixtures |
|
Commitment |
Continuous innovation, sustainability, human-centric design, cost-effective solutions |
|
Location |
Shenzhen, China |
You can trust FANXSTAR to give you lights that work for you now and later.
EU 5.8G Motion Sensor Technology
Motion Detection
You want your warehouse lights to turn on fast and right. The EU 5.8G Motion Sensor uses special microwave technology to spot movement very well. This means the sensor can light up long aisles and behind shelves without missing spots. You will not have dark areas anywhere.
The sensor works at a high frequency of 5.8 GHz. This gives you some big benefits over old sensors:
-
It stops false alarms from things that are not people.
-
It does not see through walls, so lights only turn on when needed.
-
It covers a wide area and reacts quickly.
The EU 5.8G Motion Sensor can connect many lights together. This keeps your warehouse bright everywhere and helps keep people safe.
Here is how the EU 5.8G Sensor is different from other sensors:
|
Aspect |
5.8 GHz Microwave Sensors |
Other Sensor Technologies |
|---|---|---|
|
Detection Accuracy |
High |
Lower |
|
False Alarm Rate |
Below 5% |
Higher |
|
Detection Specificity |
Excellent |
Moderate |
|
Field of View |
90°-360°, up to 12 meters |
Narrower, shorter range |
|
Environmental Resistance |
robust for warehouses |
Less robust |
This sensor turns on lights only when and where you need them. You save energy and your warehouse stays safe.
Dual PD Technology
Your warehouse needs lights that change as things change. Dual PD Technology uses both microwave and infrared sensors to spot people better. This helps the system know when people are there, not just any movement. You do not waste light when it is not needed.
Dual PD Technology gives you these features:
-
It covers the whole area with 360° detection.
-
It changes the light based on how bright the room is.
-
Zero-cross technology keeps the sensor safe from power surges.
-
It uses very little power when waiting (only 0.5W).
|
Technical Advantage |
Description |
Benefit |
|---|---|---|
|
Dual-Sensor Technology |
Microwave + IR for precise detection |
Fewer false triggers |
|
Zero-Cross Technology |
Surge protection, longer lifespan |
Less maintenance |
|
Auto Light Adjustment |
Changes brightness with ambient light |
Saves energy |
|
Wide Voltage Support |
100-277VAC, 1200W load |
Flexible installation |
This system works well even if your warehouse is dusty or busy. The EU 5.8G Sensor with Dual PD Technology keeps your lights on when you need them and saves power when you do not.
Customization Options
You can set up the EU 5.8G Sensor to fit your warehouse. The sensor has easy switches to change:
-
How far it can sense movement
-
How long the light stays on after movement
-
When the sensor turns on based on sunlight
-
How bright the light is (100%, 20%, or off)
This lets you make the lights work for different zones or times. For example, you can keep lights dim at night or make them bright during busy hours. The sensor works even if it is behind plastic or glass, so the light stays waterproof.
You can connect many lights for a long row of light. This makes sure every spot is bright and helps with emergency lighting too.
With these options, you control how much energy you use. You also make your warehouse safer and more efficient. The EU 5.8G Sensor fits your needs, not the other way around.
Features
Durability and Waterproofing
Warehouses can be tough places for lights. The Trilamp A18 has a strong polycarbonate body. It also uses an opal diffuser that lets light through well. This design keeps out dust, water, and protects from bumps. The IP65 rating means it works in wet or dusty spots. You do not have to worry about the weather or dirt. The Trilamp A18 works in very cold or hot places, from -30°C to 50°C. It is good for cold storage or hot loading docks. The light lasts up to 100,000 hours. You will not need to change it often, so you save time and money.
Fanxstar Trilamp A18 gives steady light wherever you put it.
Dimming and Control
You want to save energy and make your warehouse nice. The Trilamp A18 lets you control the light in many ways. You can change how far it senses movement. You can set how long the light stays on. You can pick when it turns on by how bright the room is. You can also set how dim or bright it gets. There are simple toggle switches for these settings. The 5.8G microwave sensor and Dual PD Technology help the light change by itself. If no one is there, the light dims or turns off. When someone comes in, it gets bright fast. This helps you use less power and keeps your warehouse safe.
Here is a quick look at the dimming and control features:
|
Feature |
Description |
|---|---|
|
Sensor Type |
Integrated 5.8G microwave motion sensor with tri-level dimming control |
|
Customizable Settings |
Detection range, hold duration, daylight threshold adjustable via eight toggle switches |
|
Dual PD Technology |
Enables automatic brightness control (lux on/off functionality) |
|
Energy Efficiency |
Automatic adjustment of light output based on occupancy and ambient light reduces power consumption |
|
User Convenience |
Easy personalization of sensor settings for specific needs and environments |
|
Sensor Sensitivity Levels |
100%, 50%, 25% |
|
Hold Time Options |
5s, 90s, 5min, 10min |
|
Daylight Threshold Options |
10Lux, 25Lux, 50Lux, Disable |
|
Stand-by Dimming Levels |
0%, 10%, 30% |
You can set the light to fit your work and save energy.
Safety Protections
You want your team and equipment to stay safe. The Trilamp A18 has built-in safety features. It protects against overcharge, low voltage, too much current, and short circuits. These features help stop electrical problems. They also help your lights last longer. There is an emergency kit option for power outages. This means you will still have light if the power goes out. You can feel safe knowing your lights protect themselves and your warehouse.
With these safety features, you can focus on your job and trust your lights to do theirs.
Benefits
Energy Savings
You want to cut costs and run your warehouse efficiently. The Trilamp A18 helps you do both. Its smart 5.8G motion sensor detects movement and adjusts the light only when needed. When no one is around, the light dims or turns off. This feature saves you a lot of energy over time.
You can set the detection range, hold time, and dimming levels. This means you control how much energy you use in each area. The Dual PD Technology also senses how bright the room is and changes the light output. You never waste power lighting empty or already bright spaces.
💡 Tip: Many warehouses see up to 60% lower energy bills after switching to sensor-controlled LED lighting.
Here is a quick look at how the Trilamp A18 5.8g motion sensor helps you save energy:
|
Feature |
How It Saves Energy |
|---|---|
|
Motion Sensing |
Lights turn on only when movement is detected |
|
Daylight Sensing |
Lights stay off if there is enough sunlight |
|
Dimming Control |
Lights dim instead of staying at full power |
|
Long Lifespan |
Fewer replacements mean less waste |
You get a lighting system that works smarter, not harder. Your energy bills drop, and your warehouse stays bright only when you need it.
Safety and Productivity
You need a safe and productive workspace. The Trilamp A18 gives you both. Its high-quality, uniform light covers every corner of your warehouse. You do not have to worry about dark spots or shadows. Workers see clearly, which helps prevent accidents.
The 5.8G motion sensor reacts fast to movement. Lights turn on right away when someone enters an area. This quick response keeps walkways and aisles safe at all times. The IP65 and IK10 ratings mean the light stands up to dust, water, and impacts. You get reliable lighting even in tough warehouse conditions.
The Trilamp A18 also supports emergency lighting. If the power goes out, the emergency kit keeps the lights on. Your team can exit safely and avoid hazards.
Customer feedback shows that the Trilamp A18 makes a real difference. Warehouses report fewer accidents and smoother operations. Workers finish tasks faster because they can see better.
“We no longer have dark corners. The light is even everywhere, and our team feels safer and works faster.” — Warehouse Manager
Flexibility
You need lighting that fits your warehouse, not the other way around. The Trilamp A18 gives you many ways to customize your lighting. You can adjust the detection range, hold time, daylight threshold, and dimming levels with simple switches. This lets you set up each zone just how you want it.
You can mount the Trilamp A18 on ceilings or walls. It comes in three sizes and power levels, so you can light small rooms or large spaces. The loop-in/loop-out wiring makes it easy to connect several lights in a row.
If your needs change, you can reprogram the settings in minutes. The Trilamp A18 also works with emergency kits and different voltage ranges. You get a lighting solution that grows with your business.
-
Adjust settings for different work zones
-
Choose from multiple mounting options
-
Connect many lights for large areas
-
Add emergency lighting as needed
The Trilamp A18 adapts to your warehouse, making it easy to keep up with changes in layout or workflow.
Installation
ounting Options
You can put up the Trilamp A18 fast and with little trouble. The sliding bracket system helps you mount it on ceilings or walls. You do not need special tools for this job. Pick the best place in your warehouse for the light. The bracket slides in, so you do not have to line it up perfectly. There are three sizes: 2ft, 4ft, 5ft and 8ft. You can use the right size for each space. The Trilamp A18 works on ceilings up to 5 meters high. On walls, it fits heights from 1.5 to 1.8 meters. The sensor covers a big area, so all spots stay bright.
Tip: The loop-in/loop-out wiring lets you link many lights together. This makes it easy to swap out old lights and saves time.
Compatibility
You do not have to change your warehouse setup. The Trilamp A18 works with most electrical systems. The 923 terminal blocks let you connect wires easily. You can use loop-in and loop-out connections. The light works with voltages from 20V to 300V. You do not need to change your wiring or fixtures. You can add emergency kits or hook up to control systems for more safety.
|
Feature |
Compatibility Benefit |
|---|---|
|
Terminal Blocks |
Easy connection to existing wiring |
|
Voltage Range |
Works with most power supplies |
|
Emergency Kit Support |
Adds backup lighting |
|
Dimming Modes |
Integrates with control systems |
Maintenance
The Trilamp A18 saves you time on upkeep. Its strong polycarbonate body keeps out dust, water, and bumps. You do not have to clean or replace it often. The LED lasts up to 100,000 hours, so you do not change it much. If you need to fix it, the sliding bracket lets you take it down fast. You can check the sensor or switch out emergency parts easily.
Check your lights often to keep them working well. The Trilamp A18 gives you steady light year after year.
Applications
Warehouse Use Cases
You need lights that work for every warehouse area. The 5.8G motion sensor fixture gives smart lighting for many jobs. You can put these lights in storage aisles, loading docks, and packing zones. The sensor sees movement, so lights turn on when you walk in. You save energy because lights dim or turn off when no one is there.
You can use the Trilamp A18 5.8g motion sensor lighting in cold storage rooms. Its waterproof and dustproof build keeps it working in hard places. You can change the settings for busy or quiet times. You can put the lights on ceilings or walls. You can link many lights together for long rows, so every spot stays bright.
Tip: You can group lights by zone. This helps you control lights for each work area and save more energy.
Here is a quick look at common warehouse uses:
|
Area |
Lighting Benefit |
|---|---|
|
Storage Aisles |
No dark spots, safe movement |
|
Loading Docks |
Fast response, clear visibility |
|
Packing Zones |
Bright, even light |
|
Cold Storage |
Reliable in low temperatures |
Emergency Lighting
You want your warehouse safe if the power goes out. The Trilamp A18 works with emergency lighting using a dual-circuit design. You can add an emergency kit to keep lights on when power fails. Workers can see exits and stay away from danger.
You can put emergency lights in important places. The easy-to-remove design lets you fix or change emergency kits fast. The sensor still works in emergencies, so lights turn on when someone comes in.
🚨 Note: Emergency lighting helps you follow safety rules and keeps your team safe all the time.
You feel better knowing your warehouse stays bright, even in emergencies. The Trilamp A4 makes sure you always have light when you need it most.
Real-World Examples
Distribution Center
You manage a busy distribution center. Every day, workers move goods in and out, and forklifts travel down long aisles. You need lighting that keeps up with this fast pace. The Trilamp A18 with the EU 5.8G Sensor gives you that edge.
When you install these lights, you see instant results. The motion sensors detect movement from forklifts and people. Lights turn on only when needed. You do not waste energy lighting empty aisles. The bright, even light helps your team see clearly. This reduces accidents and keeps your workflow smooth.
“Our energy bills dropped by almost half after we switched to Trilamp A18. The aisles stay bright, and our team feels safer.”
— Operations Manager, Regional Distribution Center
You can set different zones for high-traffic and low-traffic areas. The customizable settings let you adjust detection range and brightness. You keep busy loading docks well-lit and save energy in storage zones.
|
Area |
Lighting Setting |
Benefit |
|---|---|---|
|
Loading Docks |
High sensitivity, bright |
Safe, fast loading |
|
Storage Aisles |
Medium sensitivity |
Energy savings |
|
Packing Stations |
Constant light |
Fewer errors, clear view |
Small Warehouse
You run a small warehouse. You want smart lighting, but you need something easy to install and maintain. The Trilamp A18 fits your needs.
You mount the lights on the ceiling using the sliding brackets. The loop-in/loop-out wiring lets you connect several lights quickly. You set the sensors to cover the main work areas. When someone enters, the lights turn on. When the space is empty, the lights dim or turn off.
💡 Tip: Use the daylight threshold setting to keep lights off when sunlight fills your warehouse. This saves even more energy.
You notice fewer bulb changes because the Trilamp 18 lasts a long time. The waterproof design means you do not worry about dust or moisture. Your team works in a safer, brighter space every day.
You can make your warehouse better with the Trilamp 184 and EU 5.8G Sensor. This setup gives you smart lights, saves energy, and keeps people safe. The sensor is advanced and helps the lights work only when needed. You can change how bright the lights are in each area. The strong build means the lights last a long time and work in hard places. You spend less money and get more done for many years. Look at the main benefits below:
|
Feature |
Benefit |
|---|---|
|
EU 5.8G Sensor |
No dark spots, fast response |
|
Dimming & Control |
|
|
Durability |
Works in tough warehouse conditions |
|
Emergency Lighting |
Reliable backup during power outages |
Pick FANXSTAR’s Trilamp A18 to make your warehouse brighter, safer, and easier to run.
FAQ
How do you install the Trilamp A18 in your warehouse?
You use the sliding bracket system for quick mounting. You can attach the light to ceilings or walls. The loop-in/loop-out wiring makes connecting several lights easy. You do not need special tools.
Can you adjust the sensor settings yourself?
Yes, you can. The Trilamp A4 has eight toggle switches. You set detection range, hold time, daylight threshold, and dimming levels. You do not need extra equipment.
Is the Trilamp A18 compatible with your current wiring?
You can connect the Trilamp A18 to most warehouse electrical systems. The 923 terminal blocks support easy wiring. The light works with a wide voltage range from 20V to 300V.
How do you maintain the Trilamp A18?
You spend less time on maintenance. The strong polycarbonate body keeps out dust and water. The LED lasts up to 100,000 hours. You can remove the light easily for cleaning or repairs.
What happens if the power goes out?
The Trilamp A18 supports emergency kits. You add an emergency unit for backup lighting. Your warehouse stays lit during power outages, helping everyone stay safe.
